MOTORS AND DRIVERS, PUMP MOTORS
DC 3-6 V Mini Micro Submersible Water Pump
- Operating Voltage : 2.5 ~ 6V
- Operating Current : 130 ~ 220mA
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Outlet Outside Diameter: 7.5 mm
- Outlet Inside Diameter: 5 mm
Features :
- DC 3v to 6v submersible pump
- micro mini submersible water pump 3v to 6v
- DC water pump for DIY
- DC pump for HOBBY kit.
| Maximum Lift (mm) | 40 to 110 |
|---|---|
| Continuous Working Life (hours) | 500 |
| Driving Mode | DC, Magnetic Driving |
| Material | Plastic |
| Inner Diameter (ID) (mm) | 5 |
| Outer Diameter (OD)(mm) | 7.5 |
₹85.00
CompareYou might be searching for a pump that operates on 3-6 V and gives an output of above 70 L/H then this could be the best choice for your project.
This DC 3-6 V Mini Micro Submersible Water Pump is a low-cost, small-size Submersible Pump Motor that can be operated from a 2.5 ~ 6V power supply. It can take up to 120 liters per hour with a very low current consumption of 220mA. Just connect the tube pipe to the motor outlet, submerge it in water, and power it.
Note:
- Make sure that the water level is always higher than the motor. The dry run may damage the motor due to heating and it will also produce noise.
- This product is available in two different colors like Black and White, which will be shipped randomly so please note you will get anyone out of both colors.
Package Includes :
1 x DC 3-6 V Mini Micro Submersible Water Pump
Based on 0 reviews
Be the first to review “DC 3-6 V Mini Micro Submersible Water Pump”
Related products
-
-
MOTOR DRIVER, MOTORS AND DRIVERS
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
MOTOR DRIVER, MOTORS AND DRIVERSCNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
Width (mm) 52 Height (mm) 18 Weight (gm) 30 SKU: n/a -
MOTORS AND DRIVERS, Vibration Motor
1.5-5V DC Vibration Motor with Wire
The vibration motor is designed to operate within a voltage range of 1.5 to 5 volts DC (direct current) and is commonly used for applications that require vibration, such as in mobile devices, wearables, controllers, and more.
SKU: PH156 -
There are no reviews yet.