ARDUINO BOARDS
Showing all 11 results
-
ARDUINO BOARDS, RASBERRY PI
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
ARDUINO BOARDS, RASBERRY PI16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
Features :
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- Chainable design
- A spot to place a big capacitor on the V+ line
- 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
- This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.
Driver IC PCA9685 Length (mm) 62 Width (mm) 25 Height (mm) 15 Weight (gm) 10 SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
Arduino Mega 2560 Board Without USB Cable
The Arduino Mega 2560 is a microcontroller board based on the Atmega 2560 Microcontroller. It is one of the most powerful and feature-rich boards in the Arduino family and is commonly used for projects that require more I/O pins, memory, and processing capabilities than the standard Arduino Uno.
SKU: PH174 -
ARDUINO BOARDS
arduino Nano Board R3 With CH340 Chip With Micro USB Cable
Technical Details
- Microcontroller: ATmega328
- Operating Voltage (VDC): 5
- Input Voltage (V): 7 to 12
- Digital I/O Pins: 14
- Analog I/O Pins: 8
- DC Current per I/O Pin (mA): 40
- Flash Memory: 32 KB
- SRAM: 2
- EEPROM: 1 KB
- Clock Speed: 16 MHz
Physical Attributes
- PCB Size ( Length × Width ) mm: 43 x 18
- Weight (gm): 6
Additional Details
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Support USB download and Power
- Support for external 5V ~ 12V DC power supply
- It Supports power supply by a 9V battery
- Support ISP download
- Automatic reset during program download.
- Power OK blue LED on the bottom.
- Green (TX), red (RX), and orange (L) LED.
- +5V to AREF jumper.
- Auto-sensing/switching power input.
- Small mini-B USB for programming and serial monitor.
- ICSP header for direct program download.
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
Arduino Uno R3 DIP with Cable
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
Operating Voltage (VDC) 5 Input Voltage(Recommended) 7-12V Input Voltage (limit) 6-20V Analog I/O Pins 6 Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 DC Current per I/O Pin (mA) 40 DC Current for 3.3V Pin (mA) 50 Clock Speed 16 MHz SRAM 2 EEPROM 1 KB (ATmega328) Flash Memory 32 KB On Board LEDs On/Off, L (PIN 13), TX, RX Dimensions in mm (LxWxH) 75 x 54 x 12 Weight (gm) 28 (without cable), 54 (with cable) Shipping Weight 0.08 kg Shipping Dimensions 9 × 6 × 4 cm SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
ESP-01 ESP8266 Serial WIFI Wireless Transceiver Module
- 802.11 b/g/n Standards
- Wi-Fi Direct (P2P), soft-AP
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as an application processor
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
ESP32 CAM WiFi Module Bluetooth with OV2640 Camera Module 2MP For Face Recognization
-7%
ARDUINO BOARDS, DEVELOPMENT BOARDESP32 CAM WiFi Module Bluetooth with OV2640 Camera Module 2MP For Face Recognization
- Flash LED off: 180mA @ 5V.
- Flash LED on to maximum brightness: 310mA @ 5V.
- Deep-sleep: 6mA @ 5V min.
- Modem-sleep: 20mA @ 5V min.
- Light-sleep: 6.7mA @ 5V min.
Features :
ESP32-CAM :
- The smallest 802.11b/g/n Wi-Fi BT SoC module.
- Low power 32-bit CPU, can also serve the application processor.
- Up to 160MHz clock speed, summary computing power up to 600 DMIPS.
- Built-in 520 KB SRAM, external 4MPSRAM.
- Supports UART/SPI/I2C/PWM/ADC/DAC.
- Support OV2640 and OV7670 cameras, built-in flash lamp.
- Support image WiFI upload.
- Supports TF card.
- Supports multiple sleep modes.
- Embedded Lwip and FreeRTOS.
- Supports STA/AP/STA+AP operation mode.
- Support Smart Config/AirKiss technology.
- Support for serial port local and remote firmware upgrades (FOTA).
Specifications :
- Wireless Module: ESP32-S WiFi 802.11 b/g/n + Bluetooth 4.2 LE module with PCB antenna, u.FL connector, 32Mbit SPI flash, 4MBit PSRAM.
- External Storage: micro SD card slot up to 4GB.
- Camera
- FPC connector.
- Support for OV2640 (sold with a board) or OV7670 cameras.
- Image Format: JPEG( OV2640 support only ), BMP, grayscale.
- LED flashlight.
- Expansion: 16x through-holes with UART, SPI, I2C, PWM.
- Misc: Reset button.
- Power Supply: 5V via pin header.
- Power Consumption.
- Flash LED off: 180mA @ 5V.
- Flash LED on to maximum brightness: 310mA @ 5V.
- Deep-sleep: 6mA @ 5V min.
- Modem-sleep: 20mA @ 5V min.
- Light-sleep: 6.7mA @ 5V min.
- Dimensions (ESP32): 40 x 27 x 12 (LxWxH) mm.
- Temperature Range: Operating: -20 ℃ ~ 85 ℃; storage: -40 ℃ ~ 90 ℃ @ < 90%RH.
Package Includes :
1 x ESP32 CAM WiFi Module.
1 x OV2640 Camera Module 2MP.
SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
ESP8266 NodeMCU CH340 Board
- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- Arduino-like hardware IO
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
- ESP-12E Processor
- Easy to use breadboard friendly form factor
SKU: n/a -
ARDUINO BOARDS
LilyPad 328 ATmega328P Main Board 16M Compatible with Arduino
- The board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat!
- We now use a surface mount programming connector to keep the header from poking through.
- This version of the LilyPad now uses the new ATmega328 at 8MHz.
- Arduino 0016 supports the Pro Mini Arduino 328/8MHz/16MHZ.
- Use this setting when using this new LilyPad 328.
Technical Details
- Model Type: LilyPad
- Microcontroller Chip : ATmega168 or ATmega328V
- Operating Voltage (VDC): 2.7 ~ 5.5
- Input Voltage(Recommended) : 2.7V-5.5 V
- Analog I/O Pins: 6
- Digital I/O Pins: 14
- PWM Digital I/O Pins: 6
- Flash Memory: 16 KB
- SRAM: 1
- EEPROM: 512 bytes
- DC Current per I/O Pin (mA): 40
Physical Attributes of Lilypad Arduino Board
- Diameter (mm): 50
- Weight (gm) : 6
SKU: n/a -
