DEVELOPMENT BOARD
Showing all 15 results
-
ARDUINO BOARDS, RASBERRY PI
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
ARDUINO BOARDS, RASBERRY PI16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
Features :
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- Chainable design
- A spot to place a big capacitor on the V+ line
- 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
- This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.
Driver IC PCA9685 Length (mm) 62 Width (mm) 25 Height (mm) 15 Weight (gm) 10 SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
Arduino Mega 2560 Board Without USB Cable
The Arduino Mega 2560 is a microcontroller board based on the Atmega 2560 Microcontroller. It is one of the most powerful and feature-rich boards in the Arduino family and is commonly used for projects that require more I/O pins, memory, and processing capabilities than the standard Arduino Uno.
SKU: PH174 -
ARDUINO BOARDS
arduino Nano Board R3 With CH340 Chip With Micro USB Cable
Technical Details
- Microcontroller: ATmega328
- Operating Voltage (VDC): 5
- Input Voltage (V): 7 to 12
- Digital I/O Pins: 14
- Analog I/O Pins: 8
- DC Current per I/O Pin (mA): 40
- Flash Memory: 32 KB
- SRAM: 2
- EEPROM: 1 KB
- Clock Speed: 16 MHz
Physical Attributes
- PCB Size ( Length × Width ) mm: 43 x 18
- Weight (gm): 6
Additional Details
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Support USB download and Power
- Support for external 5V ~ 12V DC power supply
- It Supports power supply by a 9V battery
- Support ISP download
- Automatic reset during program download.
- Power OK blue LED on the bottom.
- Green (TX), red (RX), and orange (L) LED.
- +5V to AREF jumper.
- Auto-sensing/switching power input.
- Small mini-B USB for programming and serial monitor.
- ICSP header for direct program download.
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
Arduino Uno R3 DIP with Cable
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
Operating Voltage (VDC) 5 Input Voltage(Recommended) 7-12V Input Voltage (limit) 6-20V Analog I/O Pins 6 Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 DC Current per I/O Pin (mA) 40 DC Current for 3.3V Pin (mA) 50 Clock Speed 16 MHz SRAM 2 EEPROM 1 KB (ATmega328) Flash Memory 32 KB On Board LEDs On/Off, L (PIN 13), TX, RX Dimensions in mm (LxWxH) 75 x 54 x 12 Weight (gm) 28 (without cable), 54 (with cable) Shipping Weight 0.08 kg Shipping Dimensions 9 × 6 × 4 cm SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD, IOT
ESP-01 ESP8266 Serial WIFI Wireless Transceiver Module
- 802.11 b/g/n Standards
- Wi-Fi Direct (P2P), soft-AP
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as an application processor
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
SKU: n/a -
ARDUINO BOARDS, DEVELOPMENT BOARD
ESP8266 NodeMCU CH340 Board
- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- Arduino-like hardware IO
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
- ESP-12E Processor
- Easy to use breadboard friendly form factor
SKU: n/a -
CHARACTER LCD, DEVELOPMENT BOARD, DISPLAY AND LCD, OLED DISPLAY, SENSOR AND MODULES
I2C Module for 16×2 (1602) Character LCD
CHARACTER LCD, DEVELOPMENT BOARD, DISPLAY AND LCD, OLED DISPLAY, SENSOR AND MODULESI2C Module for 16×2 (1602) Character LCD
Features:-
- Operating Voltage: 5V
- Backlight and Contrast is adjusted by potentiometer
- Serial I2C control of LCD display using PCF8574
- Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
- Compatible for 16×2 LCD
- This is another great IIC/I2C/TWI/SPI Serial Interface
- With this I2C interface module, you will be able to realize data display via only 2 wires.
SKU: n/a -
ARDUINO BOARDS
LilyPad 328 ATmega328P Main Board 16M Compatible with Arduino
- The board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat!
- We now use a surface mount programming connector to keep the header from poking through.
- This version of the LilyPad now uses the new ATmega328 at 8MHz.
- Arduino 0016 supports the Pro Mini Arduino 328/8MHz/16MHZ.
- Use this setting when using this new LilyPad 328.
Technical Details
- Model Type: LilyPad
- Microcontroller Chip : ATmega168 or ATmega328V
- Operating Voltage (VDC): 2.7 ~ 5.5
- Input Voltage(Recommended) : 2.7V-5.5 V
- Analog I/O Pins: 6
- Digital I/O Pins: 14
- PWM Digital I/O Pins: 6
- Flash Memory: 16 KB
- SRAM: 1
- EEPROM: 512 bytes
- DC Current per I/O Pin (mA): 40
Physical Attributes of Lilypad Arduino Board
- Diameter (mm): 50
- Weight (gm) : 6
SKU: n/a -
ARDUINO BOARDS, MINI PROJECT, Uncategorized
PS2 Joystick Module
- Dimensions: 34 x 34 x 15 (LxWxH) mm.
- Weight: 10gm (without Hat).
- 2.54mm pin interface leads.
- Operating Voltage: 5V.
- Long service life and stable performance.
- Standard interface and electronic building blocks.
- Widely use in Arduino DIY projects.
SKU: PH100 -
DEVELOPMENT BOARD, RASBERRY PI
Raspberry Pi 4 Model-B with 8 GB RAM
- Quad-Core 64-bit Broadcom 2711, Cortex A72 Processor
- WLAN 802.11 b/g/n/ac (2,4 + 5,0 GHz)
- LAN RJ45 10/100/1000 Mbit (Gigabit LAN over USB 3.0)
- Operating Power 5V@3A via USB Type-C port
- Dual-Display Micro HDMI Ports which support H 265 Decode for 4K Video @60p
SKU: n/a -
DEVELOPMENT BOARD, RASBERRY PI
Raspberry Pi Pico (Latest & original)
Model : Raspberry Pi PICO
Operating Voltage (VDC) : 1.8 ~ 5.5
Processor : RP2040 (Dual-core Arm Cortex M0+) By Raspberry Pi
Interface : 2 x UART, 2 x I2C, 2 x SPI, up to 16 PWM channels
RAM : 264 KB
GPIO : 26 Pins
Clock Speed : 133 MHz
On Board Ports : Micro-USB 5V/2.5A DC Power Input Port
Operating Temperature (°C) :-20 to 85SKU: PH032 -
DEVELOPMENT BOARD
STM32F103C8T6 Minimum System Board Microcomputer STM32 ARM Core Board
Features :
- 100% Brand new and high-quality STM32 Board
- 72MHz work frequency.
- 64K flash memory, 20K SRAM.
- 2.0-3.6V power, I/O.
- Reset(POR/PDR).
- 4-16MHz crystal.
- Onboard Micro USB interface, you can give the board power supply and USB communication.
Model STM32F103C8T6 Core ARM 32 Cortex-M3 CPU Debug Mode SWD Length (mm) 54 Width (mm) 22 Weight (g) 9 SKU: n/a -
